When we moved into this house there was a small clothesline in the backyard. I loved using it to hang AJ’s cloth diapers to dry, but as I was hanging a load of diapers up to dry one day, the line snapped in half! It was this cheap plastic-covered synthetic line and it had been sagging pretty bad lately, so I wasn’t all that surprised when it broke. I figured if I had to replace the clothesline anyway, I might as well make it nice, functional, and strong. I bought some pulleys, cotton clothesline, and a few other supplies and made my own DIY pulley clothesline. The step by step instructions are below if you want to make one for your own yard!
When planning out my new clothesline, here were the most important features I wanted it to have:
- Strong: The clothesline needs to be strong enough not to break, even under the weight of a bunch of clothes or diapers.
- No sagging: The clothesline needs to not sag under the weight of the clothes, or stretch out over time.
- Pulley: I want to easily put clothes up and take them down, so I wanted a pulley clothesline.
- Easily removable: My husband and I are both tall, so I want to make sure that I can easily take the clothesline down when we’re not using it so that we don’t hit our heads on it.
How To Make A DIY Pulley Clothesline
- 20 minutes (time spent doing stuff)
- 0 minutes (time spent waiting around)
- 20 minutes (total project time)
- 2 pulleys
- 2 carabiners
- 2 screw hooks
- clothesline line tightener
- cotton clothesline
- 2 clothesline spreaders
- wood clothespins
- canvas clothespin bag
First you need to find a sturdy place to install your clothesline. I installed our clothesline between our detached garage and our house, but you can also attach the ends to a large tree, a sturdy fence, or a shed. Or if you want your line to run along the side or back of your house, you can install the clothesline between two large, sturdy brackets attached to your house like they did over at Homestead Revival.
When you’re ready to install your clothesline, drill a pilot hole for your screw hook, then screw the hook into your house, garage, tree, or whatever. Make sure it’s screwed all the way in, then clip one of your pulleys to it using a carabiner.
Repeat the process for the second screw hook at the other end of your clothesline.
Now it’s time to thread your clothesline! With a pulley clothesline you’ll have two parallel clotheslines running between your pulleys, one on top of the other. If you’re using a line tightener and line spreaders, the line tightener normally goes on the lower of the two clotheslines so that you can add the line spreaders as you add your clothes and it will all slide through the pulleys without the line spreader getting stuck on the tightener. But I chose to add my line tightener on the upper line so that I would have some extra room to hang clothes on the lower line. This means that I have to walk down the line and add the line spreaders to the line after I have hung all the clothes, but our line is short and it’s worth it to save the extra space for clipping up clothes!
Take your clothesline and tie it onto the loop end of the line tightener. Then take the other end of the clothesline and thread it through one pulley from the top to the bottom, then run your clothesline over to the other pulley and thread it through from the bottom to the top. Bring the clothesline back over to the first pulley so that it meets up with the line tightener. You want to leave yourself at least 3 feet of clothesline to thread through the line tightener, but you can cut off any extra clothesline beyond that. Thread the cut end through the line tightener and pull tight. (This will put your line tightener on the upper line like mine is; if you want your line tightener on the lower line, just thread the clothesline from bottom to top of the first pulley and top to bottom on the second pulley.)
If you’re using the same tightener I used, you have to pull on the body of the tightener to open up the ball bearings, slide the clothesline through the opening, and release the body of the tightener. The ball bearings will grip the clothesline tight; to tighten the line just pull on the loose end of the line hanging out the back of the tightener.
And you’re done!
I hung a canvas clothespin bag at the other end because that’s where I stand to hang clothes up and take them down.
The beauty of the pulley system is that you can completely fill your clothesline without having to walk down the line as you go! Start with the line tightener all the way at the opposite end of the line from you, then hang your first piece of clothing on the lower line closest to you. As you continue hanging clothing, pull the clothesline through the pulley until you have everything hung up and the line tightener is against the pulley closest to you. If you start hanging clothes while the tightener is in the middle, it’s going to run into the pulley closest to you and the line will get stuck halfway through and you’ll have to walk over to the other half of the line to finish hanging your clothes.
(If your line tightener is on the lower line instead of the upper line, start with the line tightener up against the pulley closest to you, then move the line out a few feet and start hanging clothes after the tightener. You can add the clothesline spreaders along with the clothes as you go, or you can add them at the end like I do.)
It’s totally normal for your clothesline to sag a bit under the weight of the laundry, and of course, cotton clotheslines will stretch out over time with use, but that’s why you have a line tightener. Once you get your laundry hung up (or any time you notice the clothesline sagging), pull the loose end of the clothesline through the line tightener until it’s tight. The lower line will probably still be sagging a bit, but that’s what the clothesline spreaders are for. Just clip them onto your clothesline in a few places and they will help keep the upper and lower lines together instead of sagging.
Once the clothes are dry, you can go back to the same side of the clothesline you started on and start unclipping clothing, pulling the lower clothesline towards you as you unclip. When you’re finished, your line tightener should be all the way back over against the far pulley again.
If you want to disassemble your clothesline when you’re not using it, loosen the line tightener slightly to give yourself some slack, and unclip one of the pulleys from the carabiner. Then you can gather up the clothesline (I like to loop it around my wrist and elbow like an extension cord) and hang it over the other screw hook so that it’s all contained together. When I want to use the clothesline again, I just clip the pulley to the carabiner again, pull the line tight through the tightener, and it’s ready to go!
One thing to note when deciding where to place your clothesline is the angle of your screw hooks. The screw hook in our house is around the corner, perpendicular to the clothesline, but the screw hook in the garage is straight in line with the clothesline. It is much worse to have the force of the clothesline pulling straight on, so if you can manage to put the hook around the corner of something to get that right angle, it’s much sturdier.
We didn’t really have a choice on the garage because there is a downspout on that corner that would be in the way of the clothesline if I put the hook around the corner, and if you don’t have any other good options, it’s totally fine to put the screw hook straight on to the clothesline. But if you have options, go with the right angle for a sturdier installation!
Do you hang your clothes to dry? We can only do it in the summer because it’s rainy and snowy the rest of the year, but I love line-drying our clothes in the summer; they smell so fresh and clean when I bring them indoors!
Shop this project:
Want to share this tutorial with your friends? Just click any of the share buttons on the left to share with Facebook, Pinterest, Twitter, etc.!